Connect with us

Aerospace

IndiGo sets 30,000 feet altitude limit for Airbus A320neos to reduce engine strain.

IndiGo Leaves Behind 37 Bags Of Passengers At Hyderabad Airport

New Delhi: InterGlobe Aviation Ltd-run IndiGo and Go Airlines (India) Ltd-run GoAir, among to first to fly the new Airbus A320neo, have been forced to find ways to deal with vexing technical snags with the Pratt & Whitney engines that power the aircraft.

IndiGo has asked its pilots to fly snag-hit A320neo planes at a lower altitude, 30,000 feet, and not the usual 36,000 feet, to reduce strain on engines even though it will mean higher fuel burn. GoAir CEO Wolfgang Prock-Schauer said in an interview in February that Pratt & Whitney “will support us properly with spare engines and other support needs to be there so we can overcome the initial phase and don’t have any flight disruptions”.
A Pratt & Whitney spokesman said it has no comment on the subject.

Advertisement

Earlier this month, the engine maker said there were no safety issues in the planes and replacement engines were being sent to India when required. Still, the Directorate General of Civil Aviation (DGCA) has asked IndiGo and GoAir to increase surveillance of these planes, besides specifying other restrictions on when and where to fly them.

In January, an IndiGo flight had a so-called rejected take-off at Mumbai. In February, a GoAir flight from Delhi had to return to the airport after an engine fire 15 minutes into the flight. In the same month, a GoAir flight had to make an emergency landing and an IndiGo flight had to fly minus passengers to Delhi from Baroda.
Spokespersons for GoAir and IndiGo declined to comment for this story.
Analysts say the two airlines are facing teething troubles that early buyers of new aircraft do. They point to Air India’s troubles with Boeing’s Dreamliner. Usually, such problems are sorted out within the first two years of a new aircraft being launched.
In this case too, “technical issues will be sorted out in one-and-a-half years”, Prock-Schauer said.
IndiGo, which was the launch customer for the A320neo, has about 411 planes on order; it has so far inducted 19 in its 131-plane fleet. GoAir flies less than half-a-dozen of them and has about 140 on order. The planes, powered by fuel-efficient engines, are key to both airlines’ low cost model.
On 21 March, Ashim Mittra, vice-president (flight operations), IndiGo, said in a note to pilots that Pratt & Whitney had proposed limiting the altitude of flying to 30,000 feet for A320neo planes to avoid a possible glitch in the engine lubrication system and that, effective 22 March, IndiGo had decided to adopt the recommendation. Mint has seen a copy of the note. Since flying at lower altitudes consumes more fuel, the note asked pilots to fuel up accordingly.
Courtesy : Live mint 

Advertisement
Advertisement

Aerospace

Boeing’s Aurora Flight Sciences Expands Columbus Plant by 50,000 Sqft

Boeing’s Aurora Flight Sciences Expands Columbus Plant by 50,000 Sqft
Credit:Aurora Flight Sciences

Aurora Flight Sciences, a subsidiary of Boeing, has launched a significant expansion of its manufacturing facility near the Golden Triangle Regional Airport in Columbus, Mississippi.

This ambitious project will add 50,000 square feet of new space, renovate 40,000 square feet of the existing facility, and introduce advanced automation equipment, robotics, and non-destructive inspection technologies. mcas boeing enhancements will support the growing demand for Aurora’s aerospace systems business.

Advertisement

Since its establishment, Aurora Mississippi has specialized in the production of advanced composite components and assemblies for both military and commercial aircraft. The company first opened in 2005 at Mississippi State University’s Raspet Flight Research Laboratory in Starkville before relocating to its current site in Columbus two years later.

Initially occupying 21,000 square feet, the facility has since grown to encompass over 120,000 square feet, featuring cutting-edge manufacturing technologies such as automated fiber placement. Aurora’s latest expansion is a strategic investment aimed at increasing production capacity for composite components like boeing titanium used in executive jets and the MQ-25TM Stingray composite skins, a key project for its parent company, Boeing.

Advertisement

Additionally, the facility will produce components for NASA’s X-66 sustainable flight demonstrator aircraft, further diversifying its portfolio. Currently employing around 100 full-time staff in Mississippi, Aurora plans to hire more than 60 additional team members by the end of 2025.

Aurora’s expansion project underscores its commitment to Mississippi’s growing aerospace and advanced manufacturing sector. The company maintains strong partnerships with Mississippi State University (MSU) and East Mississippi Community College (EMCC), contributing to research, higher education, and workforce development in advanced manufacturing.

Advertisement

Additionally, Aurora actively supports local K-12 STEM education through summer camps and collaborates with high school vocational education programs. The expansion and renovation project will be carried out in phases over the next two years, with completion expected by 2026. This development marks a significant milestone in Aurora’s ongoing growth and its role in advancing aerospace manufacturing in Mississippi.

Advertisement
Continue Reading

Trending